Waterproofing : “The walls are the foundation of your home. The weather out there will not be nice for your house’s exterior walls. It’s not enough to paint a wall. After dealing with rain, snow, wind, dust, and the heat of the outside environment, the paint will begin to peel off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
“The outer part of your home’s wall is usually covered with a lot of dust and dirt that sticks to it. To ensure the efficiency of the entire process, you need to clear off the debris and dust. The dirt and debris should be cleaned with a broom, brush, or scraper. Then use a power washer to clean it off.”
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time on your walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is ensured. Then fill them up with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The mixture of cement penetrated inside the cracks. Make sure you remove all the loose cement from the wall before you apply the cement.
Step 4: Add a layer of cement waterproofing sealer
To make sure your wall is waterproof, you need to apply a cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal on the exterior walls. Allow it to get dry.
Step 5: Pick the right water-proofer
There are many products in the market that are waterproof. You have to pick the right one for the wall. Pick the water-proofer if it is a concrete wall or a silicate one.
You can choose between a silicate-based concrete sealer and a concrete waterproofing coating. Pick a plaster waterproof Additive that will strengthen your walls.
Step 6: Apply the water-proofer
Use a brush or roller to apply the water-proofer to the walls. If you want to apply more than one coat, give a thin coat first. Add the second coating after the first has dried.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layer, you need to use a tar-based pitch after the drying of the cement waterproofer. It should be applied to your exterior wall.
After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your wall.
Step 8: Consider adding gravel
To lay the drainage pipes, you need a base below the footer. The drainage pipes will get adequate support from the gravel base. Gravel is long-lasting and provides better protection.
You need to lay the drainage pipe-cover with gravel. To back-fill the gravel, level it near the footer. Make sure the pipe is covered for at least 3 inches.
Step 9: Add a fabric barrier
Wrap the pipe with a fabric barrier. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system clean. Then back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after your Trademark.
Conclusion:
Your home will have a new life if it is waterproof. Magicrete can help you find good waterproof solutions for your walls. At a very low and affordable price, Magicrete offers you proper weatherproofing.
Heya i am for the primary time here. I came across this board and I find It really helpful & it helped me out a lot. I hope to provide something back and help others such as you aided me.
whoah this blog is great i love studying your articles. Stay up the good work! You realize, a lot of people are searching around for this information, you can help them greatly.
You made some first rate points there. I regarded on the internet for the issue and found most people will go together with with your website.